|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
TDE1767 TDE1787 Interface circuit (relay and Lamp-driver) Features Open ground protection High output current Adjustable short-circuit protection Internal thermal protection with external reset Large supply voltage range Alarm output Input voltage can be higher than VCC Output voltage can be lower than ground (VCC - VO VCC[max]) DIP-8 Description The TDE1767, TDE1767A, TDE1787, TDE1787A are a monolithic amplifiers designed for high current and high voltage applications, specifically to drive lamps, relays, stepping motors. The devices are assentially blow-out proof. The output is prois protected from short-circuits with the positive supply or drive. In addition thermal shut down is provited to keep the IC from overheathing. If internal dissipation becomes too high, the driver will shut down to prevent excessive heating. The output stays null after the overheating is off, if the reset input is low. If high the output will alternatively switch-on and off until the overload is removed. The devices operates over a wide range voltages from standard 15V operational amplifier supplies to the single +6V or +48V used for industrial electric systems. Input voltages can be higher than in the VCC. An alarm output suitable for driving a LED is provited. This LED, normally on (if referred to ground), will die out or flash during an overload depending on the state of the reset input. The output is low in open ground conditions. Table 1. Device summary Part number TDE1767DP TDE1767ADP TDE1787DP TDE1787ADP Package DIP8 DIP8 DIP8 DIP8 Packaging Tube Tube Tube Tube March 2007 Rev 2 1/16 www.st.com 16 Contents TDE1767 - TDE1787 Contents 1 2 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 2.2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 4 5 6 7 8 9 Electrical characteristcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using alarm output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 TDE1767 - TDE1787 Pin connections 1 Pin connections Figure 1. Pin connection (top view) ALARM OUTPUT INVERTING INPUT NON INVERTING INPUT GND 1 2 3 4 D03IN1475 8 7 6 5 CURRENT LIMIT VCC OUTPUT RESET 2 2.1 Maximum ratings Absolute maximum ratings Table 2. Symbol VCC VID Vl IO Vl(reset) IOA Ptot Toper Absolute maximum ratings Parameter Supply voltage Input differential voltage Input voltage Output current Reset input voltage Alarm output current Power dissipation Operating ambient temperature range Storage temperature range TDE1767A TDE1787A 60 60 - 10 to + 60 1.3 - 0.5 to + 60 - 10 to + 20 TDE1767 TDE1787 50 50 - 10 to + 50 1.2 - 0.5 to + 50 - 10 to + 20 Unit V V V A V mA mW C C Internally Limited - 25 to + 85 - 65 to + 150 - 25 to + 85 - 65 to + 150 Tstg 2.2 Thermal data Table 3. Symbol Rth(JC) Rth(JA) Thermal data Parameter Thermal resistance junction-case Thermal resistance junction-ambient Value max 30 max 80 Unit C/W C/W Note: Devices bonded on a 40 cm2 glass-epoxy printed circuit 0.15 cm thick with 4 cm2 of copper. 3/16 Electrical characteristcs TDE1767 - TDE1787 3 Electrical characteristcs TDE1767A: - 25C TA 85C, 6V VCC 55V, Io 500mA, TJ 150C TDE1767: - 25C TA 85C, 6V VCC 45V, Io 500mA, TJ 150C TDE1787A: - 25C TA 85C, 6V VCC 55V, Io 300mA, TJ 150C TDE1787: 25C TA 85C, 6V VCC 45V, Io 300mA, TJ 150C Unless otherwise specified. Table 4. Symbol VIO Electrical characteristics Parameter Input offset voltage (note 1) (measured on pin 4) Output high (TA = 25C) 5.8 5 1.5 15 TDE1787A, TDE1767A TDE1787, TDE1767 Vref 1V (figure1, note2) TDE1787A, TDE1767A TDE1787, TDE1767 VCC = 35V, t = 10ms TDE1767A: RSC = 0.22 TDE1787A: RSC = 0.33 VO = VCC -2V, t = 10ms VO = 0V, t = 10ms 130 120 1 1 1 1 700 380 150 140 170 165 8 7 4 100 60 45 60 45 mA mA mA A V V V V mA mA mV mV Test condition Min. Typ. 2 Max. 50 Unit mV ICC Power supply current Output high (VCC = VCCmax, (TJ = 150C) Output low (VCC = VCCmax, (TA = 25C) IIB VCM Imput bias current Common-mode input voltage range Input voltage range VI ISC Short circuit output current Output limit sense voltage Output limit sense voltage Vsense Vsense VO(sat) Output high VI+- VI- 50mV; RSC = 0; VCC = 30V TDE1787A, TDE1767A: TJ = 25C TDE1787, TDE1767: TJ = 25C Output saturation voltage TDE1787A, TDE1767A: TJ = 150C TDE1787, TDE1767: TJ = 150C Output leakage current Output low 1 1 1.1 1.1 1.1 1.2 1.2 1.3 100 V V V V A IOL 4/16 TDE1767 - TDE1787 Table 4. Symbol Electrical characteristcs Electrical characteristics (continued) Parameter Test condition Output source current VAH = VCC-2.5V Output sink current (in thermal shut-down) VA = 1.4V Min. -4 Typ. -5 Max. Unit mA IA Available alarm output current 5 10 2 1.4 40 mA A A A Ireset Reset input current Vth-reset Reset threhold Output leakage current open ground 10 Note: 1 2 The offset voltage given is the maximum value of different input voltage reguired to drive the output voltage whitin 2 V of the ground or the supply voltage. Input voltage range is indipendent of the supply voltage. 5/16 Schematic diagrams TDE1767 - TDE1787 4 Schematic diagrams Figure 2. 2 + 3 1 7 20 K 5K 8 Schematic diagram 210 3K 2K 600 20 pF 300 200 2K 2K 6 3.6K 10 K 1.8 K 1.1K 8.4K 300 20 K 20 K 10 K 5 3 K 4 D03IN1476 Figure 3. Equivalent schematic 7 G1 2 + SHORT-CIRCUIT PROTECTION 6 THERMAL PROTECTION 4 GROUND D03IN1477 VCC RSC G2 8 AMP INPUTS 3 1 CURRENT LIMIT ALARM OUTPUT RESET 5 OUTPUT RL Vl VCC +6V The reference input can be the inverting or non-inverting one D03IN1478 6/16 TDE1767 - TDE1787 Typical characteristics 5 Typical characteristics Figure 4. Peak short-circuit vs limiting resistor D03IN1479 Figure 5. IO (A) 0.9 Available output current vs limiting resistor D03IN1480 ICS (A) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 VCC = +30V Tamb = +25C 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 Tamb = +85C VCC = +30V Tamb = +25C 0.1 0.2 0.3 0.4 0.5 0.6 0.7 RL() 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 RL() Figure 6. Power supply current (pin 4) Figure 7. VO (sat) (V) 1.4 Output saturation voltage vs output current D03IN1482 IS (mA) D03IN1481 6 Tj = +25C IO = 0.5A Tj = +150C Output high 1.3 1.2 1.1 1.0 0.9 0.8 Tj = +25C RSC = 0 4 Tj = +150C 2 Output low 0.7 0.6 0 0 10 20 30 40 50 60 70 VS(V) 0.5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 IO(A) 7/16 Typical characteristics Figure 8. Output transistor safe operating area (pulsed)) D03IN1483 TDE1767 - TDE1787 Figure 9. Normal operating area (short circuit protected) D03IN1484 IO (A) 1.2 t= RL () no short circuit protection t= ms 10 1.0 0.8 0.6 0.4 0.1 0.2 0.3 0.4 TDE1767A TDE1767A TDE1787A TDE1767 TDE1787 0.2 0 0 10 20 30 40 0.5 0.6 0 10 20 30 40 50 60 VS(V) 50 60 TDE1787A TDE1767 TDE1787 Figure 10. Current sinking Isync (mA) 28 24 20 16 12 8 4 0 0 1 2 3 VO(V) Alarm output after thermal shutdown D03IN1485 Figure 12. Response time D03IN1487 10 0m s VS(V) Figure 11. Current sourcing Isync (mA) 14 12 10 8 6 4 2 0 0 1 2 3 VO(V) Alarm output normal operation D03IN1486 Tamb = +25C Tamb = +25C Figure 13. Response time D03IN1488 Vo (V) 0 Vo (V) 0 2.5V Vi (V) 0 Vi (V) 0 0 1 2 3 4 t(s) 0 5 10 15 20 t(s) 8/16 TDE1767 - TDE1787 Typical application 6 Typical application Figure 14. Test circuit VCC +30V 0.22 + 100 1.4V D03IN1489 Figure 15. Open load detection.4 RS RSC + RSIL 100mV R2 D03IN1492 VCC VCCR1 R2 50mV R1 IL LOAD Figure 16. Driving lamps, relays, etc... RSC VCC INPUT + CURRENT LIMITING ALARM OUTPUT GROUND 5.6K RESET OUTPUT 100K (max) RL D03IN1493 9/16 Typical application Figure 17. Common reset. TDE1767 - TDE1787 VCC RSC RSC OUTPUT + RESET GROUND ALARM 100K (max) RESET + D03IN1494 Figure 18. Parallel driving of loads up to 1 A. VCC 0.15 Vref Vi + RL 0.15 + Vref Vi RESET 100K (max) D03IN1495 10/16 TDE1767 - TDE1787 Using alarm output 7 Using alarm output Figure 19. Parallel alarm output VCC 10K 7 + 4 ALARM SIGNAL 1 + 4 D03IN1496 1 7 Figure 20. LED to VCC VCC 5.6K 7 1 4 D03IN1497 Figure 21. LED to ground VCC 7 4 1 5.6K D03IN1498 11/16 Using alarm output TDE1767 - TDE1787 Figure 22. Interface between high voltage and low voltage system. VCC+50V RSC +1 VCC+6V 0 D03IN1499 Figure 23. Increasing current up to 10A. VCC VCC + RESET ALARM OUTPUT RESET RL 0.01 CURRENT LIMITING OUTPUT 100K (max) GROUND D03IN1500 12/16 TDE1767 - TDE1787 Mechanical data 8 Mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 13/16 Mechanical data Table 5. Dim. Min A Typ 3.32 Max Min TDE1767 - TDE1787 DIP-8 Mechanical data mm Inch Typ 0.131 Max a1 B b b1 D E e e3 e4 F I L Z 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 7.95 2.54 7.62 7.62 6.6 5.08 3.18 3.81 1.52 9.75 0.020 0.045 0.014 0.008 0.065 0.022 0.012 0.430 0.313 0.100 0.300 0.300 0.260 0.200 0.125 0.150 0.060 0.384 Figure 24. Package dimensions 14/16 TDE1767 - TDE1787 Revision history 9 Revision history Table 6. Date 20-Sep-2003 3-Mar-2007 Revision history Revision 1 2 Initial release. Document reformatted, typo Figure 1 on page 3 Changes 15/16 TDE1767 - TDE1787 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16 |
Price & Availability of TDE176707 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |